100% Factory Price 100-2000kg Laundry bar Soap Production Line Hot
Sale in Africa
Introduction of 100% factory price 100-2000kg Laundry bar Soap Production Line Hot Sale in Africa:
1. the soap extruder machine or soap plodder machine use soap noodles/ soap chips as raw materials.
2. The production starts with mixing soap bar,perfume pigment or
3. Then the mixed soap noodles enters in the three roller mill by
conveyor belt, where soap thin sheets are made.
4.The soap thin sheet then converted into desired long strip soap
by the plodder machine.
5. Then the long strip soap are cut into the soap bars required
size by soap stamping machine and soap cutting machine, the size can be adjustable by your requirement, and also print your
logo on the soap bar.
6.Soap bars can be made 60g,120g,200g,260g,300g depend on your
This is soap noodles/ soap chips , it is raw material for making
laundry soap and toilet soap . they are the fatty acids derived
either from vegetable oil or animal fats used as the main
ingredient in the production of laundry soap bars and toilet soap
The main suppliers of soap noodles are in Malaysia, Indonesia,
Function of Low Price 100-300kg Laundry bar Soap Production Line
Hot Sale in Africa:
Double layer single screw working under vacuum condition to grind,
refine and press the soap material into soap bar. The above and
below screws and two orifice plates press and refine the soap
material and make the soap bar tight and the surface bright. The
motor and the reducer are separated, for long life-span and
maintenance. The below screw’s rotating speed is adjustable to
regulate the production capacity. The vacuum chamber has a vision
glass to watch the inner, the vacuum meter tests the vacuum degree.
The heater inside the outlet adopt automatic temperature control
system. The jackets of the above and below barrels are connected to
a circulating water source.
There are different capacity for 100% factory price laundry soap
production line for your choose:
- 100-200kg Laundry bar Soap Production Line
- 200-500kg Laundry bar Soap Production Line
- 500-1000kg Laundry bar Soap Production Line
- 1000-2000kg Laundry bar Soap Production Line
The combo-screw of 100% factory price 100-2000kg Laundry bar Soap
Production Line Hot Sale in Africa:
A soap plodder is an extruder with feature suitable for soap
The combo-screw allows proper noodel feeding and extraordinary
raise of process pressure up to 100bars without too much
cavitation.Such pressure allows the soap to pass through not only
one but two refining stages.
These feature are possible thanks to its innovative design with two
diameters and an intermediate conical section.
Additionally the Combo-Screw allows a very wide rotational speed
variation (from 5 to 50 tpm) and a very eddicient heat-exchange.
Delivery of 100% factory Price 100-2000kg Laundry bar Soap
Production Line Hot Sale in Africa:
Delivery by 20 feet container or40container.
Introduction of soap packing machine for laundry soap bars and
toilet soap bars making machines:
Control system: PLC
Packing speed: 30-280 bag/minutes
Packing film width: 110-320mm
Packing material: PVC, OPP, POF
There are also coder for your option:
How to Operate the soap making machines?
Firstly, Inspection before starting.
1. Check whether there are some foreign matter in the feeding and
unloading part in the plodder. Make sure it is clean.
2.Check all the lines is connect with the power.
3.Open the cooling water valve on the up and down screw in the
4. Open the air inlet valve on the vacuum pump.
5.Turn on the soap heating switch, preheat the outlet of the
plodder, temperature control at 45 ℃ ~ 55 ℃.
Second, operate the machines.
1. When the up and down screws are full of material, turn on the
vacuum pump, turn off the vacuum chamber vent valve, the vacuum
control at -0.06Mpa.
2. Make sure there are enough material for every machine.
3.Make sure the speed match with the soap cutting machiine.
4. Note that the cooling water temperature can not over 20 ℃.
Up and down screw current can not exceed the allowable range.
Third, turn off the machines
1. Make sure the material finshed in every machine.
2. Turn on the vacuum pump venting valve, and turn off the vacuum
pump. (Note: Be sure to turn on the vent valve to make sure vacuum
is at 0.)
3.Cleaning the screw of plodder after two hours when the machine
4. Turn off the power, turn off the cooling water valve, clean up
the surrounding environment.